JavaScript is off. Please enable for the site to work properly.
  • search for 3D printers and 3D printer filament

Your one stop UK shop for 3D printers and 3D printer filament

XYZ Junior Yellow PLA filament

(1 customer review)

Price: £ 24 (£20 + £4 VAT)

Da Vinci Junior Yellow PLA filament for use with the Da Vinci Junior, Da Vinci Junior 1.0w, Da Vinci Nano and Da Vinci Minimaker

SKU: RFPLCXEU0EC Categories: ,
iDig3Dprinting free delivery
iDig3Dprinting technical support
iDig3Dprinting ways to pay

Genuine Yellow XYZ Junior PLA filament for the Da Vinci Junior 3D printer and Da Vinci Junior 1.0 Wireless.

Designed to give you hours of consistent 3D printing. The da Vinci Jr. uses a different  refillable filament system to that of the other Da Vinci 3D printers. The filament spools in the da Vinci Jr are simply to replace so that refilling is easier than ever before! Also our new PLA filaments are a non-toxic, biodegradable plastic that are recyclable and safe for the environment.

Why not look at the full range of PLA filament colours we have for the Da Vinci Junior.

For information on the qualities of the different  materials available please see our guide to 3D printer filament materials.

XYZ Filament Cartridge specifications

    • Material: PLA
    • Code: RFPLCXEU0EC
    • Diameter: 1.75mm
    • Weight: 600g
    • Recommended Temperature: 210°C
    • Compatible Printers: Da Vinci Junior 1.0, Da Vinci Nano & Da Vinci Minimaker

Replacing Da Vinci Junior Filament spools

  1. First unload filament using the control panel on the printer.
  2. Open the release arm and then pull out the filament with spool axle rings. Arrange it properly for later use
  3. Retrieve filament spool to install the filament spool axle ring.
  4. Take out and separate the filament spool axle ring into its two components.
  5. Install the sensor chip. Please pay special attention to the position of the installation holes on the chip.
  6. Insert the filament spool axle ring components to either side of the filament spool, and use a cruciform screwdriver to tighten and secure the rings to the axle to complete the installation of the filament spool axle rings.
  7. Place the assembled filament spool (with the spool axle rings) on the filament holder on the left side of the printer.
  8. Pull out a section of the filament and insert it into the feed port. Caution: Pay attention to the direction the filament is being pulled out and ensure that the filament spool axle is being rotated in the correct manner.
  9. Open the release arm and push the filament all the way to the bottom so that the front end of the filament is completely inserted into the feed module.
  10. Then load filament using the control panel on the printer.

Note: This is not compatible with the Da Vinci 1.0A, the Da Vinci 1.1 Plus, the Da Vinci 2.0 and the DaVinci 1.0AiO 3D printers. We have a full range of XYZ printer cartridge colours for these printers and stock both PLA XYZ 3D printer filament and ABS XYZ 3D printer cartridges.
*Note: Images are representative

Weight 1.02 kg
Dimensions 19 × 19 × 8 cm
Reel Size


Filament type

Filament Diameter

Printer Model

, , ,


XYZ Printing

1 review for XYZ Junior Yellow PLA filament

  1. 3dprint345

    fast delivery, Very helpful support

Add a review

You may also like…

  • XYZ Junior Clear Nature PLA

  • Da Vinci Junior 0.3mm print head upgrade

  • XYZ Junior Black PLA

  • Print Bed Tape for the Da Vinci Junior