JavaScript is off. Please enable for the site to work properly.
The BCN3D sigma dual extruder 3d printer - Get great results, Print complex shapes - Winner of 3D hubs Workhorse 2017 Award!
Da Vinci Jr Filament Blue PLA for XYZ Da Vinci Junior 3D printers

Blue XYZ Da Vinci Junior Filament

£24.00 (£20.00 + £4.00 VAT)

SKU: RFPLCXEU0DB Categories: ,
iDig3Dprinting free delivery
iDig3Dprinting technical support
iDig3Dprinting ways to pay

Da Vinci Junior Blue PLA filament for use with the Da Vinci Junior and Da Vinci Junior 1.0w

Blue Da Vinci Jr Filament for the Da Vinci Junior 3D printerDa Vinci Junior 1.0 Wireless and Da Vinci Junior 3 in 1.

Designed to give you hours of consistent 3D printing. The da Vinci Jr. uses a different refillable filament system to that of the other Da Vinci 3D printers. XYZ jr filament spools are simple to replace so that refilling is easier than ever before! Also Da Vinci Junior 3D printer filament is a non-toxic, biodegradable plastic that are recyclable and safe for the environment.

Why not look at the full range of Da Vinci jr PLA filament colours we have.

For information on the qualities of the different  materials available please see our guide to 3D printer filament materials.

XYZ Da Vinci Jr Filament Cartridge specifications

    • Material: PLA
    • Code: RFPLCXEU0DB
    • Diameter: 1.75mm
    • Weight: 600g
    • Recommended Temperature: 210°C
    • Compatible Printers: XYZprinting Da Vinci Junior

Replacing XYZ Da Vinci Jr Filament spools

  1. First unload your XYZ jr filament using the control panel on the printer.
  2. Open the release arm and then pull out the filament with spool axle rings. Arrange it properly for later use
  3. Retrieve filament spool to install the filament spool axle ring.
  4. Take out and separate the filament spool axle ring into its two components.
  5. Install the sensor chip. Please pay special attention to the position of the installation holes on the chip.
  6. Insert the filament spool axle ring components to either side of the filament spool, and use a cruciform screwdriver to tighten and secure the rings to the axle to complete the installation of the Da Vinci jr filament spool axle rings.
  7. Place the assembled Da Vinci Jr filament spool (with the spool axle rings) on the filament holder on the left side of the printer.
  8. Pull out a section of the XYZ Jr filament and insert it into the feed port. Caution: Pay attention to the direction the filament is being pulled out and ensure that the filament spool axle is being rotated in the correct manner.
  9. Open the release arm and push the filament all the way to the bottom so that the front end of the filament is completely inserted into the feed module.
  10. Then load da Vinci Junior filament using the control panel on the printer.

Note: This is not compatible with the Da Vinci 1.0A, the Da Vinci 1.1 Plus, the Da Vinci 2.0 and the DaVinci 1.0AiO 3D printers. We have a full range of XYZ printer filament colours for these printers and stock both PLA XYZ Da Vinci filament and ABS XYZ Da Vinci filament cartridges.
*Note: Images are representative

Additional Information

Reel Size

600g Spool

Tones

Blues

Filament type

XYZ Junior PLA

Filament Diameter

1.75mm

Printer Model

Da Vinci Junior 3 in 1, XYZ da Vinci 1.0 Junior, XYZ da Vinci 1.0 Junior Wireless

Brands

XYZ Printing

Reviews

There are no reviews yet.

Be the first to review “Blue XYZ Da Vinci Junior Filament”